Mag Chloride and Winter Road Damage to Fleet Graphics
What Colorado's liquid deicer is, why CDOT uses it, what the residue does to wrap edges and laminate, and a rinsing schedule that keeps fleet graphics looking right through spring.

Magnesium chloride vehicle wrap damage starts as white residue on the lower panels. CDOT sprays liquid magnesium chloride deicer on Colorado highways because it costs less than sand and salt and keeps snow and ice from bonding to pavement. CDOT says the standard product works above 16°F pavement temperature and advises washing vehicles after storms. The residue clings to film edges, seams, and laminate, dulls the finish, holds grit, and can add to corrosion on exposed metal around graphics. Rinse rockers, wheel wells, lower doors, and rear doors within a few days of each storm once roads dry, using a hand wash or touchless wash and a pressure washer at least 12 inches from the film.
Mag chloride does not peel a wrap off overnight. It works slowly, at the edges, every storm, all winter.
Anyone who drives in Colorado in winter knows the chalky film that coats the lower half of every vehicle after a storm. That film is magnesium chloride, and on a wrapped fleet it settles exactly where graphics are most vulnerable: the lower edges, seams around wheel wells, and the rear doors where road spray swirls.
This guide explains what the product is, why the state uses it, what it does to vinyl and the vehicle around it, and the care routine that keeps graphics on schedule. For general lifespan, see our guide to how long vehicle wraps last in Colorado Springs.
What magnesium chloride is
Magnesium chloride is a salt compound used as a liquid deicer and anti-icer. CDOT describes its liquid deicers as salt compounds extracted from the Great Salt Lake or salt flats, applied as liquids that lower the freezing point of moisture and keep ice and snow from bonding to the road.
CDOT's deicer fact sheet lists three magnesium chloride products by pavement temperature:
| Product | Pavement temperature, per CDOT |
|---|---|
| Magnesium chloride | Above 16°F |
| Cold-temperature magnesium chloride | Below 16°F |
| APEX (magnesium chloride based) | Above minus 4°F |
The same fact sheet lists liquid deicers at 27 to 29 percent concentration. CDOT also uses solid products and sand. A 2014 CDOT release describes Ice Slicer, a mostly sodium chloride solid, and sand or sand and salt for traction.
Why Colorado uses it
CDOT uses liquid deicers because they cost less and work better for keeping roads clear than sand alone. Its fact sheet puts liquids at roughly 62 cents a gallon and says they reduce the need for sand and salt mixtures, cut plowing, and reduce after-storm sweeping.
Liquids can also go down before or during a storm. A 2014 CDOT release describes plow trucks with liquid deicer tanks in the Colorado Springs area, and a decision support system that recommends anti-icing and deicing treatments by route. The result is fewer icy roads, and a fine mist of deicer kicked up by every vehicle ahead of yours.
What it does to a vehicle wrap
Mag chloride residue mainly affects a wrap's appearance and edges, not the face of the film. Wrap films and laminates are made to handle road spray, but residue left on for weeks causes predictable wear:
- Dull laminate. Dried residue leaves a chalky haze. The longer it sits, the harder it is to wash off, and it can dull the gloss on lower panels.
- Edge buildup. Residue and grit collect along film edges and seams, where repeated scrubbing or high-pressure spray can start to lift them.
- Abrasion. Residue holds sand and grit against the film, so wiping it dry scratches the laminate.
- Hidden moisture. Salt residue holds moisture against edges and fastener holes, which keeps those areas wet longer.
Cast vinyl with laminate and clean edge finishing hold up best in these conditions. For work vans expected to stay branded for several years, APG recommends cast vinyl with laminate. Our comparison of cast vs calendered vinyl covers why calendered film struggles more here.
What it does to the vehicle around the wrap
The bigger corrosion question is the metal, not the film. A 2000 study published by CDOT, Report CDOT-DTD-R-00-10, found magnesium chloride more corrosive than sodium chloride to the bare metals it tested in cyclic lab testing, and more corrosive to copper electrical components. In a survey within the same study, 72 percent of responding Colorado trucking companies reported increased equipment wear since the state began using it.
CDOT's own fact sheet describes liquid deicers as generally less corrosive than sodium chlorides, and the study itself notes its lab conditions were accelerated and that results varied by test method. The practical takeaway for wrapped vehicles is the same either way: residue should not sit on the vehicle.
A professionally installed wrap generally does not damage sound factory paint and can help protect it from UV exposure and normal road wear. However, repainted panels, failing clear coat, rust, and existing paint damage may be affected during installation or removal. We inspect the vehicle and discuss any concerns before production.
Which panels take the most
Road spray hits the lower third of the vehicle hardest. Focus rinsing on:
- Rocker panels and lower doors. Closest to the road and the first place edges wear.
- Wheel well arches. Film edges tucked around arches collect spray from the tires.
- Rear doors and tailgates. The low-pressure area behind a van or box truck pulls spray onto the back, often coating rear graphics and phone numbers.
- Front bumper. Takes direct spray and gravel.
- Box truck and trailer lower edges. Long, flat lower panels and rivet lines collect residue; our box truck and trailer wraps page covers those surfaces.
A winter rinsing schedule
Rinse the lower panels within a few days after each storm, once roads have dried and temperatures are above freezing. CDOT advises washing vehicles after any snowstorm to remove deicer residue, and Avery Dennison's maintenance bulletin calls for cleaning graphics at least monthly, more often depending on conditions.
A practical routine for a working fleet:
- After each storm: rinse lower panels, wheel wells, and rear doors with clean water
- Every two to four weeks in winter: full hand wash or touchless wash with a mild, wax-free car soap
- Avoid brush washes: 3M recommends touchless washes because brushes can dull and scratch film, and Avery Dennison does not recommend automatic brush washes
- Dry gently: microfiber or air dry, never a dry wipe over residue
Our guide to wrapping a vehicle in winter covers care for new installs, and our vehicle wrap glossary explains terms like laminate and edge sealing.
Pressure washer rules for winter rinsing
A pressure washer is fine on a wrap if you keep it back and square to the surface. Manufacturer guidance:
- Distance: at least 30 cm, about 12 inches, from the film (3M Instruction Bulletin 6.5 and Avery Dennison IB 1.8)
- Angle: nozzle perpendicular to the surface, 90 degrees plus or minus 10. 3M says never to direct the stream at a graphic edge at an angle between 0 and 60 degrees
- Pressure: Avery Dennison lists a maximum of 1,200 psi, and 3M lists 80 bar (about 1,160 psi)
- Nozzle: a wide spray pattern. 3M specifies at least 40 degrees
- Water temperature: 3M lists 60°C (140°F) maximum, and Avery Dennison lists 70°C (158°F)
3M also advises against pressure washing perforated window film unless its edges are sealed. Coin-operated wash wands can run near or above these limits, so stand back and keep the spray wide.
Spring cleanup
When the last storm passes, give the fleet a thorough spring wash and inspection. Look for:
- White haze that a normal wash did not remove
- Lifting or dirty edges along rockers, wheel arches, and seams
- Scratches or dull patches on lower panels
- Damage from gravel, plows, or curbs
For stubborn residue, use a cleaner approved by the film manufacturer, test it on a small area first, and keep solvents off the film. Small lifted edges caught early are easier to address than a panel that has peeled back for weeks. For wraps APG installed, panel replacement is handled from the templates and artwork on file; anything else is reviewed case by case. Our vehicle wrap repair page explains the process.
The Short Version
- Magnesium chloride is a liquid deicer CDOT sprays on Colorado highways. CDOT says the standard product works above 16°F pavement temperature.
- CDOT advises washing vehicles after storms to remove deicer residue.
- Residue dulls laminate, collects grit at film edges and seams, and holds moisture against the vehicle.
- A 2000 CDOT study found magnesium chloride more corrosive than sodium chloride to several bare metals in cyclic tests.
- Rinse rockers, wheel wells, lower doors, and rear doors within a few days of each storm.
- Keep pressure washers at least 12 inches back, square to the surface, and never aimed at edges.
- Do a full wash and edge inspection in spring and address lifting edges early.
Where this information comes from
- CDOT ice and snow deicer fact sheet: codot.gov.
- CDOT research report CDOT-DTD-R-00-10, effects of deicing agents on corrosion of truck components (2000): codot.gov.
- CDOT, winter operations release, southeast Colorado (2014): codot.gov.
- 3M Instruction Bulletin 6.5, storage, handling, maintenance and removal of films: 3m.com.
- Avery Dennison IB 1.8, vehicle wrap and graphics maintenance: averydennison.com.
- 3M car wrap product care: 3m.com.
Common questions
Mag Chloride and Wraps FAQ
Does magnesium chloride damage vehicle wraps?
Residue left on for weeks dulls the laminate, collects grit along film edges and seams, and holds moisture against the vehicle. Regular rinsing prevents most of that wear.
What is magnesium chloride on Colorado roads?
It is a salt compound CDOT applies as a liquid deicer and anti-icer. CDOT says its standard magnesium chloride product works above 16°F pavement temperature, with a cold-temperature version and a product called APEX for colder roads.
Why does CDOT use magnesium chloride?
CDOT says liquid deicers are less expensive than sand and salt, reduce plowing and sweeping, and keep ice and snow from bonding to the pavement.
Is magnesium chloride more corrosive than road salt?
Evidence is mixed. A 2000 CDOT study found it more corrosive than sodium chloride to several bare metals in cyclic tests, while CDOT's fact sheet describes liquid deicers as generally less corrosive than sodium chlorides.
How often should I wash a wrapped vehicle in winter?
Rinse the lower panels within a few days after each storm and do a full hand wash or touchless wash every two to four weeks. Avery Dennison recommends cleaning graphics at least monthly.
Can I pressure wash a wrap to remove mag chloride?
Yes, with care. Keep the nozzle at least 12 inches away and square to the surface, use a wide spray pattern, and never aim at film edges at a low angle.
Which parts of a wrap does mag chloride affect most?
Rocker panels, lower doors, wheel well arches, front bumpers, and rear doors, where road spray collects.
Should I use a brush car wash in winter?
No. 3M recommends touchless washes because brushes can dull and scratch film, and Avery Dennison does not recommend automatic brush washes.
What should I check on my wrap in spring?
Look for haze a normal wash did not remove, lifting or dirty edges along rockers and wheel arches, scratches on lower panels, and gravel or plow damage.

APG: Advanced Printing and Graphics provides vehicle wraps, commercial signage, printing, apparel, promotional products, branding, and graphic design. APG is backed by industry experience dating to 2002 and has completed more than 3,000 projects and 1,000 installations. Our experience includes work for Colorado businesses and national brands such as Nike, Wells Fargo, Redken, and Warner Bros. APG was named a 2026 Best of the Springs winner in the design category by The Gazette and is a 2026 Best in Business finalist for outdoor marketing solutions with the Southern Colorado Business Journal.
Built for Colorado roads
Graphics that handle winter.
Send your fleet list and photos of each vehicle. Our estimate names the cast film and laminate we specify for Colorado winters and how edges are finished. Once the estimate is approved and the deposit is received, our team will begin the design and proofing process.