Heavy Equipment & Dump Truck Graphics in Colorado Springs
Company names, logos, unit numbers, and reflective markings for dump trucks, skid steers, excavators, loaders, water trucks, and trailers, produced in films that stand up to mud, gravel, and pressure washers.
APG: Advanced Printing and Graphics produces heavy equipment graphics in Colorado Springs for dump trucks, skid steers, excavators, loaders, water trucks, and equipment trailers. Most equipment gets cut vinyl or printed cast vinyl with laminate on doors, cabs, booms, and counterweights, plus unit numbers sized to read across a yard. Reflective film adds nighttime visibility. Equipment surfaces are rough, curved, and dirty, so preparation and film choice matter more than on a van. Graphics are installed after the surface is degreased and dry, and crews should keep pressure washers at a distance and an angle the film maker allows.
Equipment graphics live a hard life: mud, gravel, diesel, hydraulic fluid, and a pressure washer every Friday. The film and the prep decide whether the logo survives the season.
A branded dump truck or excavator is seen by every driver passing a job site and every developer deciding who to call for the next project. Unit numbers on every machine also make dispatch and maintenance easier and can help with theft recovery. But heavy equipment is not a delivery van. The surfaces are rough, the paint is often powder coat or textured, and cleaning is aggressive.
This page covers which machines and surfaces take graphics, the films that hold up on equipment, unit numbers, reflective options, required markings, and how to clean graphics without blasting them off. For trailers and box bodies, see our box truck and trailer wraps page.
- Provider
- APG: Advanced Printing and Graphics, Colorado Springs, CO
- Equipment
- Dump trucks, water trucks, skid steers, excavators, loaders, dozers, rollers, and equipment trailers
- Graphic types
- Company names and logos, unit numbers, phone numbers, reflective accents, and required commercial markings
- Materials
- Cut vinyl, printed cast vinyl with laminate, and reflective film
- Surfaces
- Painted steel and aluminum, powder coat, and fiberglass hoods; textured and heavily damaged areas are avoided
- Typical timeline
- Two to three weeks from approved estimate and deposit; most equipment graphics install in a day
- Pressure washing
- Follow film maker limits; 3M lists 80 bar maximum, 60 C water, and at least 30 cm distance
- Service area
- Colorado Springs, Monument, Fountain, Falcon, and El Paso County
Where graphics go on each machine
Every machine has a few flat, visible surfaces and many places where graphics will not survive. We plan the layout around the flat surfaces.
| Equipment | Best graphic locations | Avoid |
|---|---|---|
| Dump trucks | Cab doors, upper dump body sides, tailgate | Lower body sides hit by spray and spill, areas scraped by the load |
| Water trucks | Tank sides, cab doors, rear | Spray bar areas and fill ports |
| Skid steers and loaders | Rear counterweight, cab sides, boom arms | Bucket, lift arm pivots, steps |
| Excavators | Counterweight, cab sides, boom | Stick and bucket, track frames |
| Equipment trailers | Fenders, front rails, toolboxes, gooseneck | Deck surfaces and ramps |
The counterweight on an excavator or skid steer is often the most visible spot on a job site, because it often faces outward while the machine digs. A large logo or phone number there works like a small billboard.
Films that hold up on equipment
Equipment needs films that stretch over rivets and curves, resist chemicals, and hold through abrasion. The choice usually comes down to cut vinyl or printed cast vinyl with laminate.
- Cut vinyl. Solid color letters and logos cut from colored film. No laminate to fail, crisp edges, and long life. Best for names, numbers, and one or two color logos.
- Printed cast vinyl with laminate. Full color logos and graphics on cast film, protected by a laminate that resists scratches, fuel splash, and UV. Best for multi-color logos and larger graphics.
- Reflective film. Cut or printed reflective vinyl for names, numbers, and accent stripes that light up in headlights.
Ask each provider to identify the film series and laminate included in the estimate. APG does not install economy calendered film on vehicles, and the same reasoning applies to equipment: calendered film tends to shrink and crack on curves and rivets, especially under strong UV at 6,035 feet. Our guide to cast vs calendered vinyl explains why.
Surfaces that need care
- Powder coat and textured paint. Some powder coats resist adhesion. We test a small piece first.
- Fresh paint. A newly painted machine needs the paint to cure fully before graphics go on.
- Dents, rust, and weld seams. Film follows every flaw. Graphics are placed on sound surfaces.
Unit numbers and fleet identification
Unit numbers are often the most useful graphic on a piece of equipment. They let a dispatcher, mechanic, or site superintendent identify a machine from across a yard.
- Size for the yard. Numbers should be read from the distance people actually see them. On trucks and large machines, that usually means numbers several inches tall on each side and the rear.
- Placement on every side. Front, both sides, and rear when possible, so the machine is identifiable no matter how it is parked.
- Consistent format. The same typeface, color, and position across the fleet makes a mixed fleet look organized and speeds up dispatch.
- Theft recovery. Visible unit numbers and company names can make stolen equipment harder to resell and easier to identify.
We keep a record of your unit number layout so new machines can be matched later. Our fleet wraps page covers fleet consistency across vehicle types.
Required markings and reflective
Dump trucks and water trucks are road vehicles, and some must carry commercial markings. If your vehicle is required to display a company name, USDOT number, or other commercial markings, we can include those items in the layout based on the information you provide.
- Federal rule. The federal marking rule is 49 CFR 390.21. Whether it applies depends on the vehicle and the operation, not on the presence of a logo. Our guide to USDOT number rules for Colorado work trucks covers who needs it.
- Colorado intrastate. Colorado has its own marking rules for intrastate carriers, covered in our guide to Colorado intrastate DOT marking rules.
- Conspicuity tape. Federal conspicuity rules under 49 CFR 393.11 apply to trailers 80 inches or wider with a GVWR over 10,000 pounds built on or after December 1, 1993. They do not cover every truck, so we do not add tape as a requirement unless it applies.
Reflective graphics beyond what is required are a smart choice for equipment that works early mornings, late evenings, or along roads at night. Our reflective vehicle graphics page covers options. For required markings, see our DOT lettering page.
Preparation and installation
Prep often decides whether graphics last years or lift in a month. Equipment comes in with grease, diesel, road film, and dust in every seam.
- Clean and degrease. The graphic area is washed and degreased, then wiped with a surface cleaner before film goes on.
- Dry and warm. Vinyl applied in the cold does not conform and does not adhere correctly. Equipment that fits through our doors is installed indoors in a heated bay. Machines too large to move are scheduled on site for warm, dry days, with surfaces warmed as needed.
- Edges sealed. Edges on high-wear areas can be sealed or wrapped so pressure washing and abrasion do not catch them.
- Old graphics removed. Old decals are removed and the adhesive cleaned before new graphics go on. Our wrap removal page covers how that works.
Once the estimate is approved and the deposit is received, our team will begin the design and proofing process. Proofs show each machine with the graphics in place, including unit numbers.
Pressure washing and care
Pressure washers are one of the most common causes of lifted equipment graphics. The fix is distance, angle, and pressure, not skipping the wash.
3M's care guidance for its graphic films lists these pressure washing limits:
- Maximum pressure of 80 bar, about 1,160 psi
- Water temperature of 60 C, about 140 F, or less
- Nozzle at least 30 cm, about 12 inches, from the graphic and roughly perpendicular to it, or at least 100 cm away at a shallower angle
- Never aim the stream at the edge of a graphic at a low angle
- A spray tip with at least a 40 degree pattern and a tip guard
Other film makers publish their own limits, so follow the care sheet for the film on your equipment. Many yard pressure washers run above 80 bar, so check your washer's rating. Crews can use a wider tip, back off the graphics, or rinse them by hand. Check edges after washing and re-press or repair any lifting before it spreads.
Magnesium chloride from winter roads coats dump trucks and plow trucks for months. Rinse it off regularly, because it can dull laminates and work into lifted edges.
How an equipment graphics project runs
- Equipment list and photosSend a list of each machine with make, model, and unit number, plus photos of every side.
- Estimate and depositYou receive a written estimate by machine. Once the estimate is approved and the deposit is received, our team will begin the design and proofing process.
- Design and proofsGraphics and unit numbers are laid out on each machine's surfaces for approval.
- ProductionGraphics are cut or printed and laminated, and grouped by machine for installation.
- Installation and walkthroughSurfaces are degreased and graphics installed indoors or on site in suitable weather. We handle the installation, including equipment coordination when needed, through the final walkthrough.
Are equipment graphics a fit for your fleet?
Branding and numbering equipment pays off for most contractors. A few situations call for a different plan.
A good fit when
- Your machines work on visible job sites along busy roads
- You run several machines of the same type and need unit numbers to tell them apart
- You want a mixed fleet of trucks and equipment to look like one company
- Equipment works at dawn, dusk, or night and needs reflective markings
Look elsewhere when
- The surfaces are heavily rusted, dented, or flaking and need repair or paint first
- The machine is rented short term and cannot carry graphics
- Crews will not adjust pressure washing near graphics
The Short Version
- APG produces graphics and unit numbers for dump trucks, water trucks, skid steers, excavators, loaders, and trailers in Colorado Springs.
- Cut vinyl suits names and numbers; printed cast vinyl with laminate suits full color logos.
- Counterweights, cab doors, and upper dump body sides are usually the most visible and longest lasting graphic locations.
- Unit numbers on every side speed up dispatch and maintenance and can help with theft recovery.
- Required commercial markings depend on the vehicle and operation; we include them based on the information you provide.
- Follow the film maker's pressure washing limits; 3M lists 80 bar, 60 C water, and at least 30 cm distance.
Where this information comes from
- 3M Commercial Solutions Instruction Bulletin 6.5, storage, handling, maintenance, and removal of films: 3m.com.
- Federal motor carrier marking rules, 49 CFR 390.21: eCFR.
- Federal conspicuity requirements for trailers, 49 CFR 393.11: eCFR.
- APG installation records for equipment and dump truck graphics, Colorado Springs office.
Common questions
Heavy Equipment Graphics FAQ
Who does heavy equipment graphics in Colorado Springs?
APG: Advanced Printing and Graphics produces heavy equipment graphics in Colorado Springs for dump trucks, water trucks, skid steers, excavators, loaders, and equipment trailers, including logos, unit numbers, and reflective markings.
What vinyl is best for construction equipment?
Cut vinyl or printed cast vinyl with laminate holds up best on equipment. Cast film conforms to rivets and curves and resists shrinking, while the laminate protects printed graphics from abrasion, fuel splash, and UV.
Can you put decals on powder coated equipment?
Often, yes. Decals stick to many powder coated surfaces, but some powder coats resist adhesion, so APG tests a small piece of film on the surface before installing full graphics.
Where should a logo go on an excavator?
The counterweight is usually the best spot because it is large, flat, and faces outward while the machine digs. Cab sides and the boom are also common locations.
How big should equipment unit numbers be?
Unit numbers should be large enough to read from the distance people see the machine, which on trucks and large equipment usually means several inches tall, placed on the front, both sides, and the rear.
Will a pressure washer ruin equipment decals?
It can if the nozzle is too close or aimed at the edges. 3M lists a maximum of 80 bar, water at 60 C or less, and a nozzle at least 30 cm from the graphic for its films.
Do dump trucks need a USDOT number?
It depends on the vehicle and the operation. If your vehicle is required to display a company name, USDOT number, or other commercial markings, APG can include those items in the layout based on the information you provide.
Can graphics be installed on site?
Yes, for machines too large to bring indoors, on warm, dry days. Vinyl applied in the cold does not conform and does not adhere correctly, so on site work is scheduled around the weather.
Should equipment have reflective graphics?
Reflective names, numbers, and stripes help equipment that works at dawn, dusk, or along roads at night. Federal conspicuity tape is required only on certain trailers, not on every truck.

APG: Advanced Printing and Graphics provides vehicle wraps, commercial signage, printing, apparel, promotional products, branding, and graphic design. APG is backed by industry experience dating to 2002 and has completed more than 3,000 projects and 1,000 installations. Our experience includes work for Colorado businesses and national brands such as Nike, Wells Fargo, Redken, and Warner Bros. APG was named a 2026 Best of the Springs winner in the design category by The Gazette and is a 2026 Best in Business finalist for outdoor marketing solutions with the Southern Colorado Business Journal.
Send your equipment list
Put your name on every machine on site.
Send a list of each machine with make, model, and unit number, plus photos of every side. Our team will lay out graphics and unit numbers and send a written estimate. Once the estimate is approved and the deposit is received, our team will begin the design and proofing process.
